In development, opening to framers soon

Design it at the counter. Cut it right at the bench.

Build the frame on screen with your customer, mounts and all, and watch the price add up from your own range. When the order comes in, FramingBase plans the cuts onto your lengths of moulding and gives you the settings for the guillotine.

One email when it opens, and the odd update before then. Unsubscribe any time.

55 × 65 cm outside Moulding oak, 30 mm Glazing anti-reflective Two mounts 50 mm border Artwork 40 × 50 cm

Most shops still do it by hand

A calculator and a price book at the counter, a pencil and a tape at the bench. It works, but it’s slow, everyone does it a bit differently, and the mistakes end up in the offcut bin.

“Bear with me while I work this out…”

Quoting takes too long

You add up moulding, mounts, glazing and labour while the customer waits, then sketch the frame on the back of the job bag.

“That’s too short for anything now.”

Moulding gets wasted

Cuts are worked out at the saw one frame at a time. A fresh length gets started for a short side, and what’s left won’t make another frame.

“Let me just check the racks.”

You’re never sure what’s on the shelf

Is there enough of that moulding for this job, or does it need ordering in? Usually someone has to go and look.

The designer

Design the frame with the customer watching

Start from the size of the artwork and the frame builds out around it. Every moulding, mount and sheet comes from the range you carry, and the price updates with each choice.

  • Mounts, stacked

    Add as many mounts as the piece needs. Set the border, the reveal between each layer and any bottom weighting.

  • Their artwork in the preview

    Take a photo of the piece and it sits in the frame under the mount. Only people in your business can see it.

  • Dimensioned like a workshop drawing

    Outside size, inside size, aperture and borders, in millimetres or in inches to the nearest sixteenth. Type fractions if that’s how you measure.

  • Checks before you commit

    You’re warned when the glass, mounts and boards are deeper than the rebate, or a side is longer than a length of the moulding. A mount bigger than the sheet is refused, with the largest size that fits.

  • Stock in view

    A stocked moulding or board you haven’t got enough of is highlighted while you design. It never stops you quoting it.

  • The price as you go

    A running subtotal, tax and total for everyone on the counter. Staff don’t see your costs or margin.

Watercolour Artwork 40 × 50 cm · 55 × 65 cm outside
All changes saved
  1. Front to back
  2. MouldingOak, 30 mm
  3. GlazingAnti-reflective
  4. Mount 1Antique white · 50 mm border, bottom +10 mm
  5. Mount 2Charcoal · 5 mm reveal
  6. Artwork40 × 50 cm · photo added
  7. Mounting boardConservation
  8. Backing boardMDF, 2 mm

The layers are 8 mm deep and this moulding’s rebate is 7 mm. Check it fits before you cut.

Subtotal£74.42
VAT at 20%£14.88
Total£89.30

The cut list

Cut lists that look after your moulding

Pick the orders you’re making and FramingBase works out how to cut them from the lengths on your racks, with the machine settings on every row.

  • The fewest lengths

    Cuts are planned onto as few lengths as they’ll fit, and what’s left is kept as fewer, longer offcuts instead of lots of short ones.

  • Sides that match

    Each frame’s opposite sides come off the same length where they can, so the colour and grain match across the frame.

  • Settings for the machine

    Every cut gives the stop beam mark and table scale length for a mitre guillotine like a Morso, and the long point if you cut on a saw.

  • Only what you can cut

    Frames are offered when their moulding is on the shelf. Anything short of stock is held back, with the reason next to it.

  • Printed for the bench

    One A4 page per moulding with a box to tick on every row, then a schedule of each frame’s glazing, mount and board sizes.

  • Ticked off as you go

    Mark the list as cut when you’re finished. A frame with a row left unticked moves onto a new list, so nothing gets lost.

Oak, 30 mm 3 m lengths · 2 needed
Order 1042
Length 1 · 3000 mm Long Long Short Short Offcut 800 mm
Frame Side Qty Stop beam Table scale Long point Cut
1042-1 Long 2 25 600 650
1042-1 Short 2 25 500 550

Sizes in millimetres. The stop beam mark is the moulding’s width less its rebate; the table scale is the length at the rebate.

Every design goes on a quote

Add as many frames as the job needs, each with its own quantity. The quote is priced the same way whoever is on the counter, from the materials you picked and the prices you’ve set.

  • Moulding is charged by the metre, around the outside of the frame plus your waste allowance
  • Mounts, glazing and boards come from your sheet prices
  • Your markup is set per item type, or per item
  • Your fitting fee goes on each frame, and tax at the end
  • When the customer says yes, accept the quote and it becomes a numbered order, ready for a cut list
Example quote Watercolour, 40 × 50 cm · 1 frame
Prices include markup
  • MouldingOak, 30 mm · 2.64 m with 10% waste£27.72
  • MountsAntique white and charcoal£11.40
  • GlazingAnti-reflective£14.20
  • BoardsConservation mounting, MDF backing£3.10
  • LabourFitting£18.00
Subtotal£74.42
VAT at 20%£14.88
Customer price£89.30

Illustrative figures. Yours come from your own range and settings.

And the rest of the shop

The designer, quotes and cut lists all work from the same range, prices and stock, which you set up once.

  1. Your range, from a ready-made catalogue

    Start from a shared catalogue of supplier mouldings, mount boards, glazing and backing boards, updated from the suppliers’ own price lists. Add what you offer and override the cost or price on any item.

    Back office
  2. Stock takes

    Mark what you keep in stock and what you order in. Count the racks, enter the numbers, and see the differences as you go.

    In the workshop
  3. Currency, tax and units

    Pick your country and FramingBase sets the currency and tax rate. Work in millimetres or inches, whichever your suppliers use.

    Back office

Getting set up

There are no spreadsheets to import. Choose what you sell from the catalogue, set your prices, and you can start designing.

  1. Sign up

    Tell us your business name and country. Your currency and units follow from there.

  2. Build your range

    Pick the mouldings, mount boards, glazing and backing boards you offer from the catalogue.

  3. Set your prices

    Confirm your markup and labour fee, set your tax rate, and add the details that appear on your quotes.

  4. Design, quote, cut

    Design the frame, quote it, and when the order comes in, put it on a cut list.

Find out when it opens

We’re building FramingBase with independent framers. Leave your email and we’ll tell you when you can start using it.

We’ll only write when there’s something worth telling you.